Times are tough and we are all trying to save as much as we can! I designed this tutorial to be a cute and fashionable way for you to organize your coupons. I hope you enjoy making it as much as I did!
Charm Pack – I used Objects of Desire by Sandy Gervais
1/3 yd of Pellon decor bond interfacing
a set of magnetic fasteners
white card stock
scrap of fusible web (7″ x 4″) Therm-O-Web or Steam a Seam
PDF file of organizer tabs
1. Take 18 charms and cut them into 3 bricks and one square. You can use more than 18 charms if you’d like to have more of a variety. You will need 54 bricks and 18 squares.
Bricks = 2″ x 3″ Square = 2″ x 2″
2. Randomly pick 3 bricks and one square and piece them together in a row with the square on one end.
3. Do this a total of 18 times for 18 little rows. This goes very fast if you chain piece! I pressed all seams towards the square.
4. You can go about this randomly or you can plan in out. If you want to do it randomly skip this step. If you want to plan it like I did, lay out your 18 rows alternating the square at the top and then the bottom so that none of your brick seams line up.
6. Start at one end of the Pellon and iron one row onto the fusible side being careful not to put the iron onto the interfacing where there is no fabric yet or your iron will get very messy!
9. Repeat this with the next strip and continue until you have all 18 sewn together. You may find it helpful to roll up the extra interfacing and secure it with binding clips to keep it out of the way as you work.
The lines are to be marked at
3 rows in from the right (c)
6 rows in from the right (b)
6 rows in from the left (a)
Make sure you draw them on top of the seam and not where the seam allowance ends.
The next few steps are to put the magnetic snap in. The locations may seem odd but I promise they will match up!
12. Start by marking the locations of the snaps. The female snap location is the stitching line one to the left of line c and centered top to bottom.
13. Magnetic snaps have 4 parts. A male, a female and 2 washers. Center the washers on top of the two dots you made in step 12. Use a pen to mark the two lines on either side of the dot. Carefully use a small pair of scissors to snip part of the lines so that you will be able to put your snap through. (A seam ripper can work for this too.) You do not need to cut the entire line and smaller is better on this part as you will be able to expand the cut more if needed to push the snap through.
The next few steps involve folding the body of your clutch together. Follow the pictures as they help to show what you need to do. This may seem a bit different from what you are used to but the only complicated part is folding. You’ll be amazed at how easy this will all come together
16. Start with your piece face up.
21. One last step before we sew this all together. Measure in 1 1/2 inches from each side at the top and mark it with a pen or pencil. Measure down 2 1/2 inches on each side and mark this as well. Draw a line to connect the two dots.
24. Pin the open seam at the bottom and sew 2″ in along the bottom on each side with a 3/16″ seam so that you do not catch the folded piece in the seam. This should leave a good size opening to turn your piece.
25. Once you have sewn both sizes it is time to turn. Clip your corners a bit, take the paper off the fusible you ironed in step 24 and then turn the piece right side out. Poke out all 6 corners. I’ve found that a mechanical pencil with the lead pushed in works well.
27. You’ll notice that you still have raw edges at the bottom center. Fold in 3/16″ and carefully pin the seam together. Hand or machine stitch it closed. It is going to end up being on the inside so I did it by machine.
28. Now it is time to make the clutch have a bit of a flat bottom. To do this we want to sew across the bottom corners. Match the bottom seam to the side seam in one bottom corner. Pin on either side. Draw a line a little over an inch long across the piece.
30. Put the magnetic parts together. Iron the top to make a crease for the flap to fold naturally and you are done!
One adorable coupon clutch!
Now it is time to fill it with coupons. Print this PDF file on cardstock to make your dividers. Some may not apply to your shopping needs so print the ones that work for you. There are blank ones on the last page that you can use to add ones as well. Cut them out and put your coupons in order! You are ready to be a super savvy shopper!
Use the rest of your charm pack to make a 2nd coupon clutch for a friend! Or to make a mini version of amanda jean’s bag like i did.
I used 9 charms on each side for a 3×3 layout and didn’t trim them. So my bag pieces were 14″x14″
I also used fashion handles instead of making fabric ones. This gave me an opportunity to use my scraps from cutting the charms for the coupon clutch!
by Julie of jaybirdquilts.com!