1 Mill House Inn Honey Bun by Fig Tree Quilts
1/3 yard of Coordinating fabric (bottom of bag, handles)
1/4 yard of Coordinating fabric (tie on front, loop closure)
1/2 yard of broadcloth or coordinating fabric for lining of bag
1 button (inch or larger) for button loop closure
1/2 yard of Warm & Natural or other similar batting
Step 2 – Cut two 7″ pieces. These will be for the top of the bag.
Step 3 – Cut two 15 x 7″ pieces out of your 1/3 yard of coordinating fabric. Make sure when you cut these that there is enough fabric to make the handles which will require 2 – 21 x 4″ pieces of fabric. Sew the two 15 x 7″ coordinating fabrics onto the bottom of the two pieced pieces of fabric. Make sure that the end strip of 1st piece and beginning strip of 2nd piece are different so that when the bag is sew together there aren’t two of the same strips by each other.
Step 4 – Cut two batting pieces a little bigger than the pieced pieces you just finished. Lay pieced fabric on top of batting and quilt. If you don’t know how or don’t want to free hand quilt with your machine, you could just sew in between each stripe and at the bottom. Do this with both pieced pieces.
Step 5 – Trim extra batting off of both pieces. Place right sides together making sure the strips of fabric are together and the bottoms are together and sew around the sides and bottom using a 1/4″ seam allowance, turn fabric right side out.
Step 6- Making the tie around the middle of bag. Cut a 3″ x 37″ piece of fabric from your 1/4 yard of coordinating fabric. Fold in half width wise with right sides together and press. Cut both ends off at a 45 degree angle, or whatever looks good to you. Sew up the ends and down the side of tie (leaving an opening to turn). Now turn so right sides are out and press. stitch up small opening on side.
Step 7 – Pin tie onto the bag. Do this by folding tie in half length wise to find the middle and mark, also mark the middle of the back of the bag where the strips of fabric meet the bottom fabric. Now fold the fabric in half length wise, this just helps with making sure it’s centered on the bag when you pin it. Starting at the back of the bag where you marked, and the mark on the middle of the tie start pining tie onto bag by lining up the fold of the tie to the seam where the strips of fabric and bottom of bag come together and pin all the way around. Stop pinning when you get to the front middle two strips. This is where you’ll tie a knot. I feel like I just made that way more complicated then it needed to be, hopefully it makes some sense.
Now sew tie onto bag using about a 1/8″ seam allowance and sewing down the top and bottom of tie fabric. Remember to stop when you get to the front two middle strips of fabric.
Step 9 – Inside or lining of tote bag. Cut two 14 x 15″ pieces of broadcloth or coordinating fabric. Place right sides together and sew around the sides and bottom leaving about a 4 inch opening on one of the sides.
Step 10 – Handles. Cut two 21 x 4 inch pieces of fabric out of the 1/3 yard of coordinating fabric. Fold piece of fabric in half width wise and press. Unfold and fold outer edges into the middle crease. Now fold entire piece of fabric in half width wise and sew closed using about 1/8″ seam allowance.
Step 11 – Loop Closure. Cut a 4 x 61/2″ piece of fabric out of your coordinating 1/4 yard piece. Fold, iron and sew just like you did the handles. Now fold the sewn piece of fabric in half length wise and press. Fold both sides down at a 45 degree angle using the middle crease as your guide.
Pull the outside of bag through the opening that you left on the side of your lining fabric. Stitch closed the 4″ opening left on the side for turning. Tuck lining of bag inside and press.Now stitch around the top using a 1/8″ seam allowance.
Sew the button onto the front and you are done!!!