Gobble Gobble Layer Cake
Borders – Brown – 1/4 yard of coordinating fabric
Cream – 1 yard of coordinating fabric
Bias Binding – I purchased 3/4 yards of coordinating fabric for this but I’m sure you could get away with less. I know there are tricks to getting away with way less, but I just cut them into strips on the bias and stitched them together, even then there was a lot left over.
Back – 1 1/2 yards of coordinating fabric
Batting – 1 1/2 yards (I used a 45″ batting similar to warm and natural.)
Step 1 – Pick 14 of your favorite pieces from the layer cake and cut them each into three, 3 1/4 inch strips. If I had to do it over again I probably would have used more of the layer cake squares and not worried so much about wasting them. I would definitely consider cutting up 2 or 3 more squares.
Step 2 – Once you have cut each of your 14 squares into 3 1/4 inch strips place them in piles of three, with each pile having three different pieces.
Step 3 – Sew each pile of three strips together.
Step 5 – Arrange your strips on your floor or a big table how you want them too look. I didn’t want any pattern at all. I tried to make sure that no two fabrics that had the same design were by each other. For the table runner you will need to arrange twelve squares by 3 squares for a total of 36 squares.
For the Table Topper you want to arrange 9 squares by 9 squares for a total of 81 squares.
Sew together a row at a time and then sew your rows together, always pinning at each seam.
Step 7 – For the cream borders, cut into 5″ strips, and sew on the same way as the brown. Repeat steps 6 and 7 on your table topper also.
This is how the Table Runner and Table Topper should look with the borders sewn on.
I think everyone has a different way of doing this because everyone gave me completely different advice. Sooooo here is what worked for me.
First off draw a straight line in about one inch from the edges of your cream border all around the topper and runner. This is so the tops of your scallops are even. It would also be smart to draw a line where the down point of each scallop will be.
I used a plastic lid as my template. I tried many different sizes and the one that worked the best for me was a 5 1/2″ round lid. I first did my corners and then the four scallops in the middle and then tried to space out the rest from there. Overlapping your scallops will help a ton when it comes to getting them all even. And believe me I didn’t used a black sharpie at first. I only drew over my disappearing marker with a sharpie when I new that my scallops were exactly where I wanted them to be.
Step 10 – Make your bias binding. If you have never done this before you will need to cut 1 1/2 inch wide strips of fabric on the bias line on your cutting mat. Sew strips together end to end. You will need approx 7 – 8 yards of bias binding. Make your bias binding by first ironing strip in half. Unfold and iron one side half way into the the crease you made previously.
Step 11 – Now the fun part, sewing it on. Sew the raw edge of your bias tape with right sides of fabric together onto the topper or runner. Start in the middle of one of your scallops and line up the edges. I used 1/4 inch seam allowance and lined up the edges as I sewed.
Step 12 – For me this is the fun part. After your border is sewn onto the top, turn your piece around and stitch the back of binding on by hand. When you get to one of the inside points of the scallop just pull the binding up into the scallop and stitch.
A fun new Table Topper and Table Runner to make your Fall Holidays a little more cozy!
If you’d like some ideas of what to do with some of your left over pieces of Gobble Gobble fabric visit my blog by clicking here.