Love Is Timeless


 Hello there my Moda Bake Shop friends!! I have another quilt tutorial for you and I hope you love it just as much as I do!

I’ve named this quilt “Love Is Timeless” because it is made out of a lot of hourglass blocks and of course, hearts! I think this line is perfect for this quilt, too!!

I hope you enjoy the tutorial and come visit me, KarrieLyne, over at my blog, Freckled Whimsy, when you’re done reading!

Oh…and guess what??!! The famous Leah over at Burgundy Buttons is kitting this quilt just for you!! Hurry on over to grab yours up! Click HERE to go shopping! :D

Enjoy…. Love Is Timeless …


2 sherbet pips layer cakes
3/8 yard solid white fabric (border for heart blocks)
1/2 yard for border #1
1 1/4 yard for border #2
5 yards for backing
3/4 yard binding (8 strips 2.5″ x WOF, pieced)
template plastic
Heart Template {included in Printer Friendly Version at bottom of post}

Notes before beginning::
*All seams are 1/4″
*WOF means Width Of Fabric (selvage to selvage)
*LC means Layer Cake
*You will have to piece your backing

1. Choose 6 LC pieces that you want to use for your hearts and set them aside. You will use these for your Four Patch Heart Blocks.

Hourglass Blocks:
1.  Choose 60 layer cake pieces and trim them to 9.5”. I trim off the top and right side first just enough to cut off the pinked edge.

2.  Turn it 180 degrees and square it up to 9.5”. I put 4 LC pieces together to make trimming go faster. Just be careful to keep them lined up. Best way to do this is to turn your mat when you do the second cut instead of moving your pieces.

3.  Pair these up into 30 pairs. Remember to use contrast in choosing your pairs.

4.  Take one pair, place them right sides together and sew 1/4” seam along EACH edge of the LC pieces. Basically you are sewing a big square. Be sure to sew edge to edge, remove your piece, and begin again on the next edge. You will have no openings!  *Note* Chain piecing works well here too. Sew all of your right side edges together in a chain, trim apart, then sew your next edge on all 30 pieces, trim and repeat until you have all 30 pieces sewn. This makes the process go faster!

5.  This is the fun part!!

6.  DO NOT MOVE YOUR PIECES AT ALL UNTIL ALL 4 CUTS HAVE BEEN MADE!!

7.  Using your ruler and rotary cutter and mat, cut your piece from corner to corner, and repeat for the other corners. (You just cut an X in your piece)

8.  Now cut 4.75” from the left (cutting in half vertically)

9.  Then cut 4.75” from the bottom (cutting in half horizontally)

10. You should now have 8 quarter square triangle (QST) pieces! :)

11. Psst…you can move them now. ;)

12. Press each piece to the darker print. Take care not to iron the piece as this will stretch your bias edges. Just press.

13. You will have two sets of four QST that match. One has a seam pressed to the left, one to the right. Keep these piles the same as you cut each LC set. One pile that has all seams pressed to the right, one pile that has all it’s seams pressed to the left.  Keep these piles separate.

14. Using all these QST choose 2, both from the same pile, and both with different fabrics. Place these right sides together, matching and nesting your seams and sew along the LONG edge.

15. Press to one side. This makes up 1/4 of your block and it should measure 6” square. Square up if necessary.

16. Make 3 more.

17. Sew two pairs together, press to opposite sides.

18. Sew the pairs together. Press.

19. This is your Hourglass Block! It should measure 11.5”.

20. Make 30 Hourglass Blocks total.


Four Patch Blocks:

1. Choose 6 LC pieces and pair them up for contrast. (Note: You can use more than 6 to get a better variety in your blocks).

2. Lay 2 LC pieces right sides together, matching all edges. Sew 1/4” along each edge. (right and left)

3. Keeping your sewn edges to the right and left sides, cut piece in half. (5” from edge.)

4. Press to darker fabric. You should have two pieces that look like this.

5. Repeat for the other 2 pairs of LC pieces.

6. Pair up these pieces so each pair has different fabrics.

7. Place them right sides together with the middle seams matching. Be sure that the lighter and dark fabric pieces are opposite each other between the two pieces. See photo.

8. Sew 1/4” along each edge (left and right) so you are crossing over the seam. (refer to photo). From the edge that is sewn, cut in 1/2 way. (5” from edge”)

9. Press. You know have a Four Patch Block measuring 9.5”.

10. Repeat until you have 6 blocks.

11. Now cut 6 strips of white 1.5” x WOF and sub cut them into 12 strips measuring 1.5” x 9.5” and 12 strips measuring 1.5” x 11.5”.

12. Sew the 9.5” strips to the top and bottom of each of your Four Square blocks. Press.

13. Sew the 11.5” strips to the right and left of each of your Four Square Blocks. Press.

14. Continue this block using the Heart Template instructions below.

Heart Template:
1. Trace the heart template onto template plastic and cut it out on the line.

2. Using this template, place it on the wrong side of each of your 6 LC pieces you set out earlier and trace around the heart.

3.  Cut out each heart on the line.

4.  Attach the hearts to the Four Patch Blocks using your favourite method of applique. I placed mine in the center of each block then I sewed 1/4” away from the raw edge on the inside all the way around the heart.

5. When washed, this will cause it to fray and give it a scruffy look. :)

Finishing:
1.  Layout your blocks in a pleasing order, 6 x 6, scattering the 6 heart blocks.

2.  Sew the blocks together in each row. Press row 1 to the right, row 2 to the left, row 3 to the right, and so on.

3.  Sew your rows together. Your seams should nest nicely.

4.  Using your first border print, cut 8 strips measuring 1.5″ x WOF.  Piece these in pairs. Add border strips to the right and left sides first, trim excess. Press.  Then add to the top and bottom. Trim excess. Press.

5.  Using your second border print, cut 8 strips measuring 4.5″ x WOF. Piece these in pairs. Add border strips to the right and left sides first, trim excess. Press.  Then add to the top and bottom. Trim excess. Press.

6.  Press your quilt top well.

7.  Piece your backing then layer the backing, batting, and quilt top. Baste, and quilt as desired.

Before washing, your quilt should measure approximately 76″ square.

I hope you have enjoyed this tutorial! If you make this quilt, please oh please share it with me? You can email a photo of it to me HERE or you can add it to my Flickr Group HERE.  I would love to feature them on my blog! :)

Much Love and Happy Quilting!!

KarrieLyne
{http://www.freckledwhimsy.com}

Latest posts by Karrie Lynne Winters (see all)